Prototype electrochromic device and dye sensitized solar cell using spray deposited undoped and ‘Li’ doped V2O5 thin film electrodes

Lithium (Li) (0–5 wt%) doped V₂O₅ thin films were spray deposited at 450 °C onto ITO substrates. Structural analysis using X-ray diffraction and Raman spectroscopy revealed orthorhombic phase of the films. In addition to the V₂O₅ phase, presence of VO₂ peaks due to high deposition temperature is also evident from structural and optical characterization. The non-stoichiometric nature of the films due to loss of the terminal O atom was confirmed from Raman spectroscopy. The direct band gap, indirect bandgap, and phonon energies were also calculated from optical studies. Different charge states of vanadium ions present in the film were identified from X-ray photoelectron spectroscopy study. Results from cyclic voltammetry experiments reflected significant differences between the undoped and Li doped V₂O₅ samples. Transport properties by Hall-effect measured at room temperature indicated significant increase in conductivity, carrier concentration and mobility of V₂O₅ thin films on doping with Li. A Dye Sensitized Solar Cell (DSSC) was fabricated using mobility enhanced 5 wt% Li doped V₂O₅ film as photoanode and its efficiency was found to be 2.7%. A simple electrochromic cell is fabricated using undoped V₂O₅ thin film to demonstrate the colour change.     

Lithium ion conduction and ion-polymer interaction in poly（vinyl pyrrolidone） based electrolytes blended with different plasticizers

Poly（ethylene oxide）, poly（vinyl pyrrolidone）（PEO/PVP）, lithium perchlorate salt（Li Cl O4） and different plasticizer based, gel polymer electrolytes were prepared by the solvent casting technique. XRD results show that the crystallinity decreases with the addition of different plasticizers. Consequently, there is an enhancement in the amorphousity of the samples responsible for the process of ion transport. FTIR spectroscopy is used to characterize the structure of the polymer and confirms the complexation of plasticizer with host polymer matrix. The ionic conductivity has been calculated using the bulk impedance obtained through impedance spectroscopy. Among the various plasticizers, the ethylene carbonate（EC） based complex exhibits a maximum ionic conductivity value of the order of2.7279 10 4S cm 1. Thermal stability of the prepared electrolyte films shows that they can be used in batteries at elevated temperatures. PEO（72%）/PVP（8%）/Li Cl O4（8%）/EC（12%） has the maximum ionic conductivity value which is supported by the lowest optical band gap and lowest intensity in photoluminescence spectroscopy near 400–450 nm. Two and three dimensional topographic images of the sample having a maximum ionic conductivity show the presence of micropores.     

Fragmentation of fuel pellets during transport via a belt conveyor: A design of experiment study

This work investigates the proportion of generated fines in a pilot-scale experiment using a belt conveyor and commercial fuel pellets. For this, a belt conveyor with a length of 3.1 m was used and operated at varying conditions: speeds, percentages of material loading on the belt, two combinations of the inclination angle of the belt and the falling height, and a different number of handling steps. We considered a design of experiments approach based on response surface methodology to investigate the effect of different conditions on the potential of fines generation. Moreover, a comparison between the results of the belt conveyor and three common benchmark experimental approaches (tumbling box, rotary impact tester, and mechanical compression test) was made. Results show that the number of handling steps and the combined effect of drop height and inclination angle directly affected the fines generation. However, the tested belt speed range and the level of loading were of lower significance. A polynomial quadratic model was derived based on the regression analysis and showed a high accuracy to predict the proportion of fines. Moreover, the tumbling box method showed good potential to predict the proportion of fines in a belt conveyor when transported several times.     

A class of deformational flow test cases for linear transport problems on the sphere

A class of new benchmark deformational flow test cases for the two-dimensional horizontal linear transport problems on the sphere is proposed. The scalar field follows complex trajectories and undergoes severe deformation during the simulation; however, the flow reverses its course at half-time and the scalar field returns to its initial position and shape. This process makes the exact solution available at the end of the simulation, and facilitates assessment of the accuracy of the underlying transport scheme. A procedure to eliminate possible cancellations of errors when the flow reverses is proposed.     

Optimal flow conditions of a tracheobronchial model to reengineer lung structures

The high demand for lung transplants cannot be matched by an adequate number of lungs from donors. Since fully ex-novo lungs are far from being feasible, tissue engi-neering is actively considering implantation of engineered lungs where the devitalized structure of a donor is used as scaffold to be repopulated by stem cells of the receiv-ing patient. A decellularized donated lung is treated inside a bioreactor where transport through the tracheobronchial tree (TBT) will allow for both deposition of stem cells and nour-ishment for their subsequent growth, thus developing new lung tissue. The key concern is to set optimally the boundary conditions to utilize in the bioreactor. We propose a pre-dictive model of slow liquid ventilation, which combines a one-dimensional (1-D) mathematical model of the TBT and a solute deposition model strongly dependent on fluid velocity across the tree. With it, we were able to track and drive the concentration of a generic solute across the airways, look-ing for its optimal distribution. This was given by properly adjusting the pumps' regime serving the bioreactor. A feed-back system, created by coupling the two models, allowed us to derive the optimal pattern. The TBT model can be easily invertible, thus yielding a straightforward flow/pressure law at the inlet to optimize the efficiency of the bioreactor.     

Oxygen deficiency in oxide films grown by PLD

The incorporation of oxygen atoms in oxide films grown by pulsed laser deposition depends upon the oxygen pressure and laser power density. By carefully controlling these two parameters it is possible to control the oxygen deficiency in the samples, and thus to change their physical properties from insulating and transparent to absorbing and conducting. By using X-ray diffraction, Rutherford backscattering spectroscopy and resistivity measurements, we show that depending upon the oxide materials oxygen deficiency in the films can induce either the growth of stable sub-oxide phases or the formation of nanocomposite films by phase separation. The first case corresponds to oxides with a mixed valency cation like Ti, which leads to the formation of stable, crystalline and highly conductive TiO_x sub-oxide phases. The second case is well described by the indium tin oxides (ITO) in which a large oxygen deficiency leads to metallic clusters embedded into a stoichiometric matrix, i.e. nanocomposite films. This phenomenon is due to the fact that sub-oxides of these compounds are not stable and thus the oxygen deficiency induced a phase separation.     

Electrical investigation of some fluorides of composition A2MII+MIII+F9 by impedance spectroscopy

The ac conductivity of three fluorides of A₂M^II+ M^{III +} F₉ type, Sr₂NiAlF₉, Sr₂ZnGaF₉ and Ba₂MnCrF₉, between 293 and 773K, has been analyzed within a combined complex impedance and modulus formalism. The antiferroelectric-paraelectric phase transition of Sr₂ZnGaF₉ has been characterized. A hopping mechanism for charge carriers is suggested for the three materials; their electrical performance are relatively weak. Sr₂NiAlF₉ and Sr₂ZnGaF₉ can be considered as ionic conductors of the F- ion. On the contrary, the conductivity in Ba₂MnCrF₉ is rather of an electronic nature.     

Effect of Temperature on Henry's Constant in Simple Mixtures

Abstract

The molecular theory of dense fluids is progressing rapidly and its extension to mixtures is well underway. The purpose of this note is to call attention to a possibly serious difficulty in comparing experimental Henry's constants with those calculated from theory. The difficulty arises because whereas theorists choose temperature and density as independent variables, experimental equilibrium measurements on mixtures are often made along the saturation line where (at fixed composition) temperature and density are not both independent variables. Unless Henry's constants are defined with care, the effect of temperature on Henry's constants calculated from molecular theory may be qualitatively different from that observed.